Double Bed Jacquard for Brother Punch Card Machines
- Use 2 to 4 thin yarns (like 2/24 for standard or 3/12 for bulky) and appropriate tension – too heavy of yarn won’t work for FNR
- Insert the Fine Knitting Bar
- Attach color changer; prepare yarn mast with yarn (yarn on floor to L side under changer)
- Decide pattern and get it ready on machine – punch card in place; turned off
- Set machine/ribber to do FNR (Full Needle Rib) Pitch H on desired number of N on both beds
- Insert extension rail on left side – If whole bed is being used, insert both sides
- Ribber must have same number of needles on both sides of 0 for DBJ
- End N’s on main bed
- Insert all yarns into Color changer except #1 (background color)
- T 0/0 Attach yarn #1 (background yarn) into carriages and do zig/zag row (cannot do Broken Toe Cast On with FNR)
- Hang Comb and weights; set and knit circular rows; remove settings
- T 0/0 – (tight for ribbing) Do short number of rows of ribbing (like 2) COL
- If doing rows before engaging punch card for the design – knit those now
- KC knob
- Tension 2/2 if using 1 strand 2/24 for standard
- K 1 row to right to select N
- Turn punch card on; set to elongate if using 3/4 color design
- Push in both Part buttons on the main bed carriage
- FOR BIRDSEYE DBJ- [Firmer and more dense fabric] On 850 ribber carriage push both N buttons up to PR; Push in and rotate both lili buttons to engage them; Slide lever on bottom to lili
- FOR 2 ROW STRIPE DBJ – [Looser weave and ends up wider than birdeye] Do not change any settings on the ribber
- K 1 row to left
- Watch punch card to see when to change yarn and to which # of yarn
- Change yarn color to # on punch card
- K 2 rows (always watching yarn as you begin row to make sure only one yarn is in carriages)
- Change yarn color
- Begin to weight with additional double claw weights on both sides after about 25 rows and keep moving them up; after about 100 rows, hang triangle combs and weight with large ribber weights from ribber comb – move 2 sides ones constantly to keep stitches from catching on a gate peg – reach to back and check for caught yarn frequently; can leave ribber comb attached without weights until it reaches almost to bottom of stand – then remove
- Repeat color changes and moving weights until design is completed or desired length is reached
- Turn off all carriage settings and punch card
- If you are knitting plain rows after design and before ribbing knit those now
- T 0/0 – Make sure you have ribbing color in carriage
- K 2 – 5 R ribbing (to match length of beginning) – end on L
- Move carriage tensions to 8
- K 1 loose row to right
- Loop through a Loop Bind Off – left to right
- You may copy, print and use any of the info on my blog. Please do not copy and repost anywhere on the internet without contacting me to get my permission. Thank you, Ann
- Ann Huppert (GrammaAnn)
I have tried so many other step by step instructions for DBJ and have had such inconsistent results. With your instructions, I finally “get it”. Thank you so much.
LikeLike
Wow – that is fabulous! I am so happy it was a help to you! 🙂 Ann
LikeLike
This an awesome! Blog. Thanks so much for your teachings.
LikeLike
Thank you! I am so happy it is helpful! 🙂 Ann
LikeLike
I didn’t know a color changer was available for the Brother 260 Bulky.
LikeLike
Yes the KRC900 is for bulky or standard. It is the only Brother one that fits both. 🙂 You have to move a part to change from a standard to a bulky.
LikeLike
Hi GrammaAnn. I miss reading your contributions on knittingparadise, since I can no long log onto the site.
At any rate, at the beginning of the instructions you state (at No.2) to insert fine knitting bar. What is this and how do you do it? I might have one, but have never used in all these years.
LikeLike
Thank you for your sweet comments! The fine knit bar is a long piece of skinny plastic that comes with the ribber. But it actually goes on the main bed right along the edge of the bed behind the gate pegs. So many got thrown away through the years. It helps all the stitches knit off correctly. You can buy one after market on ebay. 🙂 Ann
LikeLike
Oh, well, I didn’t throw it, but it’s sitting on my radiator for the past 2 years. Thanks! I’ve been wanting to learn double jacquard. This is good to know. Without it, will the technique not work?
LikeLike
Jude, I’m so glad you have it! Use it! 🙂 If you don’t you will have to watch every row to make sure all stitches are knitting off correctly. I’d just put it in!
LikeLike
Well, I tried dbj… all I get is stripes on both sides. There’s no picture. What could I be doing wrong?
LikeLike
It’s probably a setting you don’t have quite right. Do you have both slip buttons pushed in? Unless your carriage is malfunctioning? Go through the instructions one line at a time and check your settings. 🙂
LikeLike
Thank you. I’ll try again. Yes, both slip buttons were pushed in. I used a kh270, is there a different consideration for this model?
LikeLike
I am sorry I am unfamiliar with the 270.
LikeLike
Well, even more perplexing… I just tried it on my ayab hacked kh910 and it worked great!
LikeLike
Well, even more perplexing… I just tried it on my ayab hacked kh910 and it worked great!
BTW, good in Colorado. I used to live in springs before I came east.
LikeLike
Thank you for all you help. As it turns out there was a bad spring in the carriage and one of the levers was not recoiling cause all the fiasco of my DBJ attempts this morning. Thank you so much for sharing your skills, talent, and knowledge of machine knitting. I pray that the Almighty Father blesses you for sharing and your giving, which has been a value that cannot be purchased.
LikeLike
Hi Jude, I wondered if it was not your carriage. 🙂 Thank you for your sweet comments – I really appreciate it! 🙂 Ann
LikeLike
Hi GrammaAnn,
Question,
You said that both end needles need to be on the top bed, I was just reading the KRC 900 manual and it states that the left end needle must be a purl. Can you clairify?
I just got my color changer in… I am determined to learn this Double Jacquard technique!
LikeLike
HI Jude, Yes please follow the manual. Sometimes I have followed someone’s instructions and to be honest I doubt it makes any difference. 🙂 So whatever you like better! I’d love to see what you make! 🙂 Ann
LikeLike